Our Product Collections

It is a rear-seat cover with a supported platform that bridges the footwell gap behind the front seats. This model combines three removable rigid panels with raised front, rear and side coverage.

A soft hammock mainly suspends fabric between headrests, while this back seat extender for dogs hard bottom model adds rigid panels under the main surface. The panels create a flatter standing and lying area, but correct vehicle support and installation still matter.

The standard platform is marked 52 in wide by 24.8 in deep, approximately 132.1 × 63.0 cm. The supplied diagram also shows a 15.7 in rear panel, 21.7 in front panel and two 15 in side wings.

No universal fit is confirmed. Measure the usable rear-seat width, seat depth, footwell gap, headrest arrangement and door clearance, then compare them with the 52 × 24.8 in layout before ordering.

Different seat positions can make the supported section sit at an angle or reduce usable depth. Preserve a safe driving position first, then check that all three panels remain flat and supported without contacting seat rails or sharp edges.

The three-panel floor is designed to bridge the gap between the rear bench and front seatbacks. Actual coverage depends on vehicle geometry and seat position, so inspect both footwells after installation.

The supplied care graphic shows three removable rigid load-bearing panels. Their exact material, thickness and load rating are not supplied and should be confirmed on the production specification.

No verified load capacity is supplied for this SKU. Do not borrow a 400 lb or similar claim from another listing; capacity must be tested with the final panel material, seams, straps and installed support conditions.

Sagging can occur if panels are misplaced, damaged, partly inserted or not adequately supported by the vehicle layout. Install every panel fully, tension straps evenly and press-test the surface before loading the dog.

No. It manages space and protects the seat but is not presented as a crash-tested restraint. Use an independently verified automotive harness, secured carrier or crate suitable for the dog and vehicle.

No. A collar can concentrate force on the neck during sudden movement. Follow the instructions for the chosen automotive restraint and use a properly fitted harness or secured carrier/crate.

Yes. The images show access points that keep rear buckles reachable through the cover. Route the selected restraint without twisting it and confirm that the opening does not close around or obstruct the buckle.

The zipper layout allows one side to fold for a separate rear seating position. Confirm that the passenger has a normal seat belt, footwell and door path and that the remaining dog platform stays fully supported.

Compatibility is not automatic. Follow the vehicle and child-restraint manufacturer instructions, keep required anchors and belt paths accessible, and do not allow the extender or straps to interfere with the child seat.

They allow selected side sections to open, close or fold when changing configuration. Inspect zipper alignment before use and keep fabric and zipper pulls clear of door latches and seat rails.

The raised side wings cover common paw-contact areas near the rear doors. Coverage varies by vehicle, and the panels must not block handles, window controls, airbags or door latches.

The coated surface and inner TPU barrier provide a water-resistant direction, but seams, access openings, wear and installation can allow moisture through. Remove spills promptly and do not market the product as submersible or leakproof everywhere.

No scratch-proof claim is confirmed. The textured PU surface is intended for normal paw contact, but claws, chewing, sharp hardware and repeated abrasion can mark or puncture it.

Vacuum loose hair, wipe the PU surface and dry it before folding. For deeper cleaning, remove all three rigid panels and follow the sewn care label for the textile cover.

No. The rigid panels must be removed first. The supplied graphic places the textile cover in a laundry bag, but the final production care label controls the approved temperature, cycle and drying method.

Dry the cover completely, slide each rigid panel fully into its intended sleeve and close every zipper. Lay the product flat and check that the panel joints meet evenly before installing it in the vehicle.

The supplied folded size is approximately 25.2 × 17.3 in. Let the cover dry first, fold only along intended seams and store it without sharply bending or warping the removable rigid panels.

Confirm that the surface is flat and dry, all three panels are correctly positioned, buckles are closed, straps are evenly tensioned and seat-belt openings remain clear. Close each rear door slowly to make sure no fabric or hardware is trapped.

A flatter surface may be easier for some dogs to stand or lie on than an open-footwell hammock, but this is not a medical product. Add an appropriate non-bulky comfort layer only if it does not hide buckles, openings or panel joints.

Yes, subject to the selected material, logo method, color, trim, dimensions, packaging and order quantity. Structural or load-related changes require separate engineering and validation.

Approve the exterior dimensions, panel count and material, zipper layout, strap lengths, buckle type, mesh, pockets, seat-belt openings, care method, folded size and final pack-out. Keep the signed sample and specification tied to one stable model code.

MOQ depends on the base model, PU color, trim, quilting, panel specification, logo method and packaging. Archova can separate standard-product MOQ from any higher MOQ for custom materials or structural changes.

The source confirms a folded size of 25.2 × 17.3 in but not the final carton, packaged weight, units per carton or container quantity. These values are confirmed after the final product and accessory specification is approved.